Perko 0607 Manuel d'utilisateur télécharger pdf

Fig. Nos. 0606 & 0607 Series L.E.D. Utility Light

The above lights are not designed for navigational use.

MOUNTING INFORMATION

Read all instructions before proceeding.

MOUNTING TEMPLATE

1). These instructions show the orientation of the light after the proper

mounting location has been determined.

2). These lights are supplied with the proper circuit for operation on a

nominal 12 volt system.

3). These lights contain no user serviceable components.

4). Draw a 8-1/2 inch long reference line through the center of the select-

ed mounting location.

5). Cut out the mounting template below.Tape it on the mounting surface

such that the reference line (drawn above) passes through the exact

center of the template.

6). Drill four holes through the template as indicated for the #6 mounting

screws and two or three holes 3/32” to 1/8” diameter to accommodate

the wiring as indicated on template.

7). Wiring should be done by a qualified marine electrician. Attach

supply connections to the light, making sure to wire in accordance with

both A.B.Y.C. Standard E-9* and U.S. Coast Guard Safety Standards

for Boat Electrical Systems (33CFR 183)* Observe polarity.

8). Attach the light to the mounting surface using #6 mounting screws.

* The above referenced standards can be obtained from:

(1). American Boat & Yacht Council, Inc.

613 Third Street, Suite 10

Annapollis, MD 21403

(2). U.S. Coast Guard

Washington, D.C. 20593

(or your local C.G. office)

Perko, Inc.

16490 N.W. 13th Avenue

Miami, FL. 33169-5707

www.perko.com

03/09

0606INS1

Cut out Template on Dotted Line

Ê

This is a 3/4”

circle in order

to scale internet

printed

templates

Fig. Nos. 0606 & 0607 Series L.E.D. Utility Light

The above lights are not designed for navigational use.

MOUNTING INFORMATION

Read all instructions before proceeding.

MOUNTING TEMPLATE

1). These instructions show the orientation of the light after the proper

mounting location has been determined.

2). These lights are supplied with the proper circuit for operation on a

nominal 12 volt system.

3). These lights contain no user serviceable components.

4). Draw a 8-1/2 inch long reference line through the center of the select-

ed mounting location.

5). Cut out the mounting template below.Tape it on the mounting surface

such that the reference line (drawn above) passes through the exact

center of the template.

6). Drill four holes through the template as indicated for the #6 mounting

screws and two or three holes 3/32” to 1/8” diameter to accommodate

the wiring as indicated on template.

7). Wiring should be done by a qualified marine electrician. Attach

supply connections to the light, making sure to wire in accordance with

both A.B.Y.C. Standard E-9* and U.S. Coast Guard Safety Standards

for Boat Electrical Systems (33CFR 183)* Observe polarity.

8). Attach the light to the mounting surface using #6 mounting screws.

* The above referenced standards can be obtained from:

(1). American Boat & Yacht Council, Inc.

613 Third Street, Suite 10

Annapollis, MD 21403

(2). U.S. Coast Guard

Washington, D.C. 20593

(or your local C.G. office)

Perko, Inc.

16490 N.W. 13th Avenue

Miami, FL. 33169-5707

www.perko.com

03/09

0606INS1

Cut out Template on Dotted Line

Ê

This is a 3/4”

circle in order

to scale internet

printed

templates

Drill 3/32” to 1/8” Dia. holes for electric wires (2) or (3) places

Drill for #6 Screws (4) places

Drill 3/32” to 1/8” Dia. holes for electric wires (2) or (3) places

Drill for #6 Screws (4) places

1

MOUNTING TEMPLATE 1

Résumé du contenu

Page 1 - MOUNTING TEMPLATE

Fig. Nos. 0606 & 0607 Series L.E.D. Utility LightThe above lights are not designed for navigational use.MOUNTING INFORMATIONRead all instructions

Modèles reliés 0606

Commentaires sur ces manuels

Pas de commentaire