Perko 1283 Manuel d'utilisateur
Naviguer en ligne ou télécharger Manuel d'utilisateur pour Éclairage Perko 1283. PERKO 1283 User Manual Manuel d'utilisatio
- Page / 1
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Cat. No. 1236 Series Reduced Glare Design Combination Masthead and All-Round (Anchor) Light
Cat. No. 1283 Series Reduced Glare Design Combination Masthead and All-Round (Anchor) Light
The above lights are designed for use on power driven vessels under 12 meters (39.4 ft.) in length, operating at a nominal 12 volt system.
I
n order to comply with 72 COLREGS and U.S. Inland Navigation Rules, the following must be adhered to:
MOUNTING INFORMATION
Read all instructions before proceeding.
1). These instructions show the orientation of each light. For proper light selection, positioning and configuration, refer to A.B.Y.C. Standard A-16*,
the 72 COLREGS* and the U.S. Inland Navigation Rules . These lights are supplied complete with 12 volt bulbs (Cat. No. 0338DP1CLR 12V,
5W).
2). These lights are designed to be mounted on a horizontal surface.
3). These lights are furnished for mounting such that the long dimension of the mounting base is parallel to the fore-aft centerline of the boat.
If a mounting is desired such that the long dimension of the mounting base is perpendicular to the fore-aft centerline of the boat, substitute
instruction d) below for instructions a) to c).
a). Draw a 4 inch long reference line through the center of the selected mounting location and parallel to the fore-aft centerline of the boat.
b). Cut out the mounting template below. Tape it on the mounting surface such that the reference line (drawn above) is directly underneath the
reference line marked on the template.
c). Drill 2 holes through the template to accommodate #8 round head mounting screws. Drill one 3/8 inch hole to accommodate the electric
wiring. (Proceed with instruction #4 below).
d). Special instruction only for mounting with the long dimension of the mounting base perpendicular to the fore-aft centerline of the boat:
1). Draw a 4 inch long reference line through the center of the selected mounting location and perpendicular to the fore-aft centerline of
the boat.
2). Remove the holding screw (see illustration) and rotate light assembly on the tube 90° in one direction then the other until a second hole
appears on the tube. Re-insert the holding screw into the light assembly such that is enters the new tube hole to anchor the assembly
90° from its original position.
3). Cut out the mounting template below. Tape it on the mounting surface such that the reference line (drawn above) is directly underneath
the reference line marked on the template.
4). Drill 2 holes through the template to accommodate #8 round head mounting screws. Drill one 3/8 inch hole to accommodate the electric
wiring.
4). Attach supply connections to the light making sure to wire in accordance with both A.B.Y.C. Standard E-9* and U.S. Coast Guard Safety
Standards for Boat Electrical Systems (33 CFR 183)*.
The supply leads are coded as follows:
WHITE: Forward compartment (masthead light) positive supply lead.
RED or GRAY: Aft compartment (when energized with the forward compartment: all-round light) positive supply lead.
BLACK: Negative supply lead. (CAUTION: Negative lead connected to case. To avoid energizing case, observe polarity).
Electrical connections are to be made such that only the forward compartment (masthead light) is energized with the other running lights (side-
lights, sternlight etc.) while underway. Both compartments are energized simultaneously by themselves to create the all-round (anchor) light. Be
sure to use double pole switches, otherwise feedback will cause all lights in the system to be energized at the wrong time. See wiring diagram.
5). Mount the base in accordance with both the template and instruction #6 below.
6). Make sure the top of the light is vertical during operation (see illustration) and arrow on the top cover points ahead (not astern), with the reference
mark parallel to the fore-aft centerline of the boat.
* The above referenced standards can be obtained from:
(1) American Boat & Yacht Council Inc. (2) U. S. Coast Guard Perko, Inc.
613 Third Street, Suite 10 Washington, D.C. 20593 16490 N.W. 13th Avenue
Annapolis, MD 21403 (or your local C.G. Office) Miami, FL 33169-5707
www.perko.com
DRILL 3/8”
HOLE FOR
ELECTRICAL SUPPL
Y
DRILL FOR #8 SCREWS
CUT ALONG BROKEN LINE
MOUNTING TEMPLATE
Cat Nos.
1236001CHR
1236DP1CHR
1236002CHR
1236DP2CHR
1283000CHR
1283DP0CHR
REFERENCE LINE
HOLDING
SCREW
NO
TE:
TOP OF LIGHT MUST
BE VERTICAL DURING
OPERATION
AHEAD
U
SCG APPROVAL
33 CFR 183.810
Visibility: 2nm
T
ested By: IMANNA Labs.
D
ate: 10/8/03
M
eets ABYC A-16
WIRING DIAGRAM FOR COMBINATION
MASTHEAD/ANCHOR LIGHTS
•
Double pole, double throw
switch (center off)
•
One position illuminates
running lights (masthead,
side & stern)
• Other position illuminates
anchor light (forward & aft
compartments of combi-
nation masthead/anchor
light)
1
1/06
1236INS1
1
Résumé du contenu
Page 1 - SCG APPROVAL
Cat. No. 1236 Series Reduced Glare Design Combination Masthead and All-Round (Anchor) LightCat. No. 1283 Series Reduced Glare Design Combination Masth
Produits connexes et manuels pour Éclairage Perko 1283
(2 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.905 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels